NewLife® Intensity 10 Oxygen Concentrator Service Manual AirSep Cor

MN134-1 rev B 02/14 5 2.0 Operational Check and Oxygen Concentration Test 2.1 Description of Operation Air is drawn into the NewLife Inten

MN134-1 rev B 02/14 6 oxygen monitor detects lower than therapeutic levels of oxygen concentration. The alarm remains on until you correct the al

MN134-1 rev B 02/14 7 3.0 Patient Instructions 3.1 Instructions It is important that patients thoroughly understand how to operate the AirS

MN134-1 rev B 02/14 8 4.0 Provider Instructions 4.1 Instructions To ensure that the unit’s output of oxygen is within specification, you must

MN134-1 rev B 02/14 9 4.1.5 Recording Maintenance As the Equipment Provider, you can record all routine maintenance and repairs performed on the

MN134-1 rev B 02/14 10 5.0 Main Components 5.1 Components The design of the AirSep NewLife Intensity 10 Oxygen Concentrator allows for easy acc

MN134-1 rev B 02/14 11 5.3 Compressor The compressor is the “pump” within the oxygen concentrator that pushes the room air into the bottom of th

MN134-1 rev B 02/14 12 5.3.2 Capacitor Replacement The capacitor starts the compressor. If the compressor cannot start, the capacitor may be d

MN134-1 rev B 02/14 13 b. Feed/waste coil = 850ohms +/- 10% 2. 220-240VAC units a. EQ coil = 4,300ohms +/- 10% b. Feed/waste coil = 3,100ohms

MN134-1 rev B 02/14 14 If replacement is necessary, you must replace both sieve beds at the same time. Sieve Bed Removal To remove sieve b

MN134-1 rev B 02/14 ii Expedited Product Warranty Check service is always at your fingertips with AirSep: http://www.airsep.com/Support/W

MN134-1 rev B 02/14 15 A green light that fails to illuminate indicates a disconnected or faulty solenoid coil or an electrical malfunction in tha

MN134-1 rev B 02/14 16 4. Remove the 2nd stage intake resonator, which is held in place by Velcro. 5. Remove the securing nut that holds the pro

MN134-1 rev B 02/14 17 5.9.2 Product Regulator Cleaning or Rebuilding Clean or rebuild the product regulator if the regulator cannot be adjusted

MN134-1 rev B 02/14 18 I/0 Power Switch Installation Follow the removal procedure for the I/0 power switch in reverse order to install a new pow

MN134-1 rev B 02/14 19 3. Open the plastic twist clamps. 4. Cut the tie-wraps (located near the power cord push-on connectors). 5. Disconnect t

MN134-1 rev B 02/14 20 6.0 Troubleshooting 6.1 Operating Pressure Test Testing the operating pressure is a useful diagnostic tool when a conc

MN134-1 rev B 02/14 21 6.2 General Troubleshooting Before reviewing the troubleshooting chart, the following steps may be useful to isolate any m

MN134-1 rev B 02/14 22 6.3 Troubleshooting Chart Problem Probable Cause Solution Unit does not run. Constant audio alarm with I/0 power switch

MN134-1 rev B 02/14 23 Problem Probable Cause Solution Compressor runs with intermittent high pressure alarm and low oxygen concentration. Res

MN134-1 rev B 02/14 24 Problem Probable Cause Solution Cabinet fan does not turn. Faulty electrical connections. Faulty cabinet fan. Check el

MN134-1 rev B 02/14 iii Table of Contents Section 1.0 Introduction 1.1 Equipment Provider Responsibility 1 1.

MN134-1 rev B 02/14 25 6.4 Tool Kit and Pressure Test Gauge The tools needed for you to properly service the NewLife Intensity 10 unit are list

APPENDIX • Exploded drawings Wiring Diagram – Intensity 10 120V A Wiring Diagram – Intensity 10 220/240V B Control Pa

MN134-1 rev B 02/14 A WIRING DIAGRAM INTENSITY 10 120V

MN134-1 rev B 02/14 B WIRING DIAGRAM INTENSITY 10 220/240V

MN134-1 rev B 02/14 C ITEM PART NUMBER DESCRIPTION ITEM PART NUMBER DESCRIPTION 1 BK016-1 BRACKET, FLOWMETER, DUAL 13 FA002-1 FASTENER, TIE WRAP

MN134-1 rev B 02/14 D ITEM PART NUMBER DESCRIPTION ITEM PART NUMBER DESCRIPTION 1 BT001-2 BATTERY, HOLDER 15 SC002-1 SCREW, TEMP SWITCH 2 BT002-

MN134-1 rev B 02/14 E ITEM PART NUMBER DESCRIPTION ITEM PART NUMBER DESCRIPTION 1 BE186-1R BEDS 6A CD011-2 CORD, POWER, US-STYLE 2 CA034-1 CABIN

MN134-1 rev B 02/14 F ITEM PART NUMBER DESCRIPTION 1 RG088-1 REGULATOR (ONLY) 2 TA132-1 TANK, MIXING, ASSY PRODUCT TANK/REGULATOR ASSEMBLY

MN134-1 rev B 02/14 G ITEM PART NUMBER DESCRIPTION ITEM PART NUMBER DESCRIPTION 1 VA290-3 VALVE, BLOCK (ONLY) 3B VA117-1 VALVE, COIL, 220V 2 VA0

MN134-1 rev B 02/14 H NUMBER NUMBER 1 CL007-1 CLAMP, HEAT EXCHANGER 6 F0104-1 FITTING, ELBOW, HEAT EXCHANGER 2 CO306-1R COMPRESSOR, ASSY, 120V 7

MN134-1 rev B 02/14 iv Section 5.0 Main Components 5.1 Components 10 5.2 Cabinet Removal 10 5.2.1 Removing Side Panel

MN134-1 rev B 02/14 I NUMBER NUMBER 1 BE002-4 BED, TUBE 9 F0001-2 FITTING, ELBOW, TOP CAP 2 BE005-2 BEDS, LEFT CAP ASSY, TOP 10 F0105-7 FITTING,

MN134-1 rev B 02/14 v Section 6.0 Troubleshooting 6.1 Operating Pressure Test 20 6.1.1 High Operating Pre

MN134-1 rev B 02/14 1 1.0 Introduction 1.1 Equipment Provider Responsibility All Equipment Providers of the NewLife® Intensity 10 Oxygen Concen

MN134-1 rev B 02/14 2 1.2 Important Notice and Symbol Explanations As you read the manual, pay special attention to the WARNING, CAUTION, and NOT

MN134-1 rev B 02/14 3 Method for disposing of waste: All waste from the NewLife Intensity 10 (patient circuit, etc.) must be disposed of using app

MN134-1 rev B 02/14 4 1.3 Functional Specifications Oxygen Concentration: 2-9 LPM: 92% +3.5/-3% 10 LPM: 90% +5.5/-3%